??摘要：本文介紹了霍爾傳感器在智利的應用。霍爾電流傳感器主要用于隔離和轉換交流、直流、脈沖等復雜信號。根據霍爾效應理論對電流信號進行信號控制轉換后，可直接被AD、DSP、PLC、二次儀表等設備獲取。霍爾電流傳感器廣泛適用于電流監測、電池應用、逆變器、太陽能發電等領域的采集和反饋管理、直流柜、直流電機驅動、電鍍、變頻器、UPS伺服控制系統。具有響應快、測量范圍廣、精度高、過載能力強、線性度好、抗干擾性能好等特點。

??Abstract:This article introduces the application of the Hall Sensor used in chile. Hall current sensors are mainly used to isolate and convert AC, DC, pulse and other complex signals. After signal control of current signals are converted according to the Hall Effect Theory, they can be directly acquired by AD, DSP, PLC, secondary instruments and other devices. Hall current sensors are widely applicable for acquisition and feedback in the current monitoring, battery application, inverter, solar power management, direct current cabinet, DC motor drive, electroplating, welding, frequency converter, UPS servo control systems. They feature the quick response, wide range of measurement, high precision, strong overload capacity, good linearity and excellent anti-interference performance.

??1.項目概述 Project overview:

??做鋰電池的公司，需要使用直流霍爾傳感器將直流電流傳輸?shù)?-20mA模擬信號輸出。客戶在確認了輸入輸出和工作電源后，選擇了AHKC-EKA和AHKC-EKAA。

??The company that do lithium batteries need to use DC Hall sensors to transmit DC current to the 4-20mA analog signal output. After confirming the input and output and working power, the customer chose AHKC-EKA and AHKC-EKAA.

??2.開口式霍爾傳感器優點Advantages of open type Hall sensor

??與傳統直流電流計量一般采用分流器或互感器測量方法相比，開口式霍爾傳感器具有以下優點：

??1）原邊副邊絕緣強度高，可達AC 12kV隔離；

??2）無插入損耗；

??3）動態性能好：響應時間小于20us速度di/dt高于20A/us

??4) 安裝時無需拆卸原邊電纜或母排，特別適用于不允許斷電設備的改造施工。

??Compared with the traditional DC current measurement method generally adopted by shunt or transformer, the open-type Hall sensor has the following advantages:

??1) High insulation strength of primary side and secondary side, up to AC 12KV isolation;

??2) No insertion loss;

??3) Good dynamic performance: the response time is less than 20uS and the tracking speed Di /dt is higher than 20A/ uS

??4) There is no need to disassemble the original side cable or bus during installation. It is especially suitable for the transformation and construction of equipment that is not allowed to lose power.

??3.產品選型Product Selection

??4.應用Application

??霍爾電流傳感器主要應用在工廠改造直流配電系統中，如電廠直流電源系統改造、光伏，UPS,電機系統等，它能將系統中原邊直流電流信號轉換成為標準DC± 5V或4-20mA輸出，起到了監測和電氣隔離作用，可與多回路監控儀表或其他電氣測量儀表配套使用。

??Hall current sensor is mainly used in factory transformation of DC power distribution system, photovoltaic, UPS, motor system, etc. It can convert the primary DC current signal in the system into a standard DC ± 5V or 4-20mA output, which plays a role in monitoring and electrical isolation , It can be used with multi-loop monitoring instruments or other electrical measuring instruments.

??5 .結論Conclusion

??開口式霍爾電流傳感器因其結構簡單、安裝方便、運行可靠等良好的適用性，在直流系統應用中發揮很大的作用。

??Open-end Hall current sensor plays an important role in the application of DC system because of its simple structure, convenient installation, reliable operation .

??參考文獻 Bibliography

??1.Solutions For Enterprise Micro-grid System 2021.04